¶ 1. Introduction to the Atelier Control Area
Figure 1
- ①Frame/Repeat:
- Short Press: Start edge tracing / Stop edge tracing (executes the most recent processing task from the APP).
- Long Press (3 seconds or more): Repeat engraving (executes the most recent processing task from the APP).
- Double Click: Cancel engraving.
- ②Start/Pause:
- Short Press: Start engraving / Pause engraving.
- Long Press (3 seconds or more): Enter Wi-Fi setup mode.
- Double Click: Clear fault status.
- ③Wi-Fi Indicator:
- Off: Not connected to the network.
- Flashing White: Wi-Fi configuration in progress.
- Steady Green: Wi-Fi connected.
- ④Status Indicator:
- Steady White: Powered on, standby.
- Steady Green: Laser operating.
- Flashing Green: Paused.
- Steady Red: Alarm / Fault.
- Steady Blue: Accessory mode.
- ⑤ Focus Knob: Adjusts the height of the galvo platform for focusing.
- ⑥ Accessory Port: Connects accessories such as rollers or chucks.
- ⑦ USB Key: USB key slot. The machine can only start when the USB key is inserted (pre-installed at the factory). The laser will not operate without the USB key.
- ⑧ Computer: Computer connection port, connects to the PC via a Type-C cable.
- ⑨ Power: Power input port.
- ⓪ Emergency: Emergency stop / Power on-off.
¶ 2. Atelier Installation
Reference: Atelier installation video.
Click to play video on YouTube
Note:
- Install the exhaust pipe first.
- Install the positioning strip as needed according to usage requirements.
¶ 3. Atelier Network Connection
Reference: Atelier PC Connection Video & Atelier Mobile Connection Video.
Click to play video on YouTube
Click to play video on YouTube
Note:
- When using AtomStack Studio on PC or mobile, no additional setup is required; the device is ready to use once connected.
- Atelier supports mobile Wi-Fi connection and mobile hotspot connection. During file transfer, do not switch the APP to run in the background.
- When using LightBurn software, you must first import the configuration file, or set the "Origin" to the top-left corner in "Device Settings." Otherwise, the engraving may appear mirrored (upside down). Make sure the baud rate is set to 460800, as shown in Figure 1.
Figure 1
- If the square image border appears curved during framing, recalibration is required. Please refer to the Atelier Galvo Calibration Video.
Click to play video on YouTube
- When engraving thin materials, ensure the object is securely fixed; otherwise, the internal fan may move the material. You can use the provided masking tape to secure the edges or the provided positioning strip.
- When engraving edges, do not enable overscan. If a "border exceeded" warning appears when starting, adjust the position or check whether overscan is enabled. If engraving results appear distorted or misaligned, also check for the "border exceeded" warning and whether overscan is enabled.
¶ 4. Atelier Galvo Calibration Tutorial
Reference: Atelier Galvo Calibration Video.
Note:
- Preparation: Follow the instructions in Chapter 7, Atelier Focusing, to ensure correct focus and secure the material.
- Calibrating with AtomStack Studio (PC): Click "Settings" → "Calibration" (see Figure 2). When setting the X-axis and Y-axis scale factors, first reset the scale factors to 1.000, click "Save Parameter" to save the settings, and then click "Update Data" before performing the calibration.
Figure 2
- Scaling: Click "Start", then measure the actual side length of the engraved square border. Enter the measured values into "Size Coefficient Calculation" to calculate the scale factor. For example, the default engraving file size is 100 mm × 100 mm, but the actual engraved result is 112 mm × 117 mm. After entering the values, the calculated X-axis scale factor is 0.893 (see Figure 3). The Y-axis is adjusted in the same way.
Figure 3
- Note: After entering the calibration data, click "Save Parameter". If you need to modify the calibration parameters, click "Update Data". After calibration is complete, perform an engraving test and confirm whether the engraved pattern matches the size of the engraving file. If the sizes do not match, please check the calibration parameters again.
- Curve: If the border appears curved when clicking "Frame" (see Figure 4), the curve parameter must be adjusted. For example, if the Y-axis curve value is 1.060, enter this value into the Y-axis curve setting.
Figure 4
¶ 5. Atelier Rotary Operation Tutorial
Reference: Atelier Rotary Device Connection and Usage Video.
Click to play video on YouTube
Note:
- Rotary Selection:
- Atelier only has an expansion output port (with auto-recognition), so only R6, R8, and R8 PRO rotary accessories can be used.
- Threaded risers must be installed (see Figure 5).
- Use the provided USB cable (see Figure 6) to connect to the machine's Accessory Port for automatic recognition.
- Not compatible with R1, R1 Pro, R2, R3 Pro, R1-B, or R2-B rotary accessories.
Figure 5
Figure 6
- AtomStack Software Settings: When using AtomStack Studio, parameters must be set for the detected device. Roller (R6): No parameter setting required. Chuck (R8): Set the material's circumference or diameter (see Figure 7).
Figure 7
- LightBurn Settings: When using LightBurn, rotary parameters need to be configured. Rotary Type: Select Roller for R6, Chuck for R8. Rotary Axis: Select the Y-axis. Parameter Settings: For R8 (Chuck), set the rotation speed to 160 mm per rotation (fixed). Enter either the material diameter or circumference. For R6 (Roller): set the rotation speed to 50 mm per rotation (fixed), rotary diameter to 16 mm (fixed), and enter either the material diameter or circumference. (See Figure 8)
Figure 8
- Focus Adjustment: After placing the material, refocus is required. For focusing instructions, refer to the "Atelier Focusing" section.
¶ 6. Atelier Conveyor Feeder Operation
Reference: Atelier Conveyor Feeder Connection and Usage Video.
Click to play video on YouTube
Note:
- When using, ensure the USB port of the conveyor feeder faces away from the user (toward the right side of the machine).
- The conveyor feeder must be placed horizontally, with the bottom groove aligned to the Atelier base. Secure it with the provided screws to prevent vertical movement. Refer to the R4 manual (see Figure 9).
- AtomStack Studio: The device will be automatically recognized after connection. Click OK to start using (see Figure 10).
- LightBurn: Manually set the engraving machine working size to 350 mm × 120 mm to use the conveyor feeder (see Figure 11).
Figure 9
Figure 10
Figure 11
¶ 7. Atelier Focusing
Reference: Atelier Focusing Video.
Click to play video on YouTube
Note:
- The optimal focus is achieved when the two small red dots coincide (approximately 151 mm).
¶ 8. Software Engraving Parameter Test Tutorial
Reference: Atelier Engraving Parameter Test Tutorial Video.
Click to play video on YouTube
Note:
- This function requires a genuine LightBurn software (version 1.3.01 or above) or AtomStack Studio.